1
Post your Shack, Shop, Repair room / Re: Radio repair bench
« on: December 28, 2016, 11:08:28 AM »
Thank you, could have not done it without your help.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Post your Shack, Shop, Repair room / Radio repair bench
« on: December 27, 2016, 12:50:46 PM »
Thanks Buddy. I was trying to attach an image. I read your post on image size.
3
Post your Shack, Shop, Repair room / Re: My Ham Radio station and workshop/Man-cave
« on: December 26, 2016, 12:10:49 PM »
You have a window, that's a plus.
5
Home Brew And Tech Forum / Flux receipe
« on: December 14, 2016, 11:55:01 AM »
I ordered the rosin and have the IA, wondered what the mixture is for thru hole soldering.
6
Basic beginner Electronics / Re: Troubleshooting
« on: December 13, 2016, 11:56:47 AM »
Chris, if you going to open up a Brick and Mortar store there is a lot to consider, depending on the state/county where you live you may need a business license, tax ID, etc.
Then you will need a business plan, people, inventory, etc.
I'm not trying deter you but unless you have a very good tech and are in a prime location it's going to be tough.
Good luck with you adventure
Then you will need a business plan, people, inventory, etc.
I'm not trying deter you but unless you have a very good tech and are in a prime location it's going to be tough.
Good luck with you adventure
7
New member welcome / Re: New member saying hello
« on: December 13, 2016, 11:51:28 AM »
Welcome Aboard Frank.
8
Electronic Video Blog / Re: #85 Shop Talk General Comments
« on: December 12, 2016, 01:06:59 PM »
Thank You.
9
Electronic Video Blog / Re: #85 Shop Talk General Comments
« on: December 12, 2016, 08:11:59 AM »
Hi Budddy
I wouldn't loose any sleep over the copyright trolls.
I'm interested in making my own flux, could you point me to where you get your supplies?
Thanks
Jim
I wouldn't loose any sleep over the copyright trolls.
I'm interested in making my own flux, could you point me to where you get your supplies?
Thanks
Jim
10
CB Radio Repair manuals and documentation / Wanted, factory service manual for cobras
« on: November 27, 2016, 07:53:10 PM »
Does anyone know where I can get a "hold in my hands" paper manual for the Cobra 29 and 25 LTD?
I tried the flea-bay site and they have everything but, I think the Sam"s I'm looking for is 207 and 217.
I have found info on the cb tricks, but would like to have a printed copy of the schematics.
Is it possible to call Cobra, or would that be a wasted 4 hours on the phone?
Jim
I tried the flea-bay site and they have everything but, I think the Sam"s I'm looking for is 207 and 217.
I have found info on the cb tricks, but would like to have a printed copy of the schematics.
Is it possible to call Cobra, or would that be a wasted 4 hours on the phone?
Jim
11
Electronic Video Blog / Re: #80 Realistic HTX-100 diagnostic and repair
« on: November 27, 2016, 10:03:30 AM »
You are welcome, I'm sure I'll have a million questions, I post them in the correct section.
Jim
Jim
12
Electronic Video Blog / Re: #80 Realistic HTX-100 diagnostic and repair
« on: November 27, 2016, 12:38:22 AM »
Buddy, Thanks for taking your time to post the videos, I'm a learnin.
I didn't know If I should post here on on utube.
What do you use to hold your camera? I saw one of the guys used the manfrotto flex shaft, I still have a large magic clamp from my photography days.
Santa came early I got a HP 8656B signal generator, brand new old stock with the manual still in plastic, now I got to learn to use it.
Thanks again for the video.
Jim
I didn't know If I should post here on on utube.
What do you use to hold your camera? I saw one of the guys used the manfrotto flex shaft, I still have a large magic clamp from my photography days.
Santa came early I got a HP 8656B signal generator, brand new old stock with the manual still in plastic, now I got to learn to use it.
Thanks again for the video.
Jim
Pages: [1]