Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Crambone

Pages: [1]
1
Ham Radio Circuits and Repair / Re: TS-520 Hi Voltage Cap Question
« on: November 20, 2019, 09:39:21 PM »
Replace them now don’t wait for them to go and possibly cause issues.

2
Ham Radio Circuits and Repair / Re: RCI 2995DX NO POWER
« on: November 19, 2019, 07:18:39 PM »
So I pulled Q66 2SB754Y and replaced with new and still the same voltages? I tested the one Installed and the one I pulled and they tested good.
             old.       new
hfe        184       144
Ube       536mv   547mv
Ic.         6.3ma    6.4ma

I popped the collector pin off and Its showing 13Vdc but when installed it drops to 2.4Vdc Im thinking something shorted from the Collector to the TP7?
So I pulled the alignment board from TP7, 8 & 9 and tested continuity of each to ground. TP7 shows continuity but only for around 3 second then stops then shows again 3 seconds ..........! So it only does it under power if I unplug power it doesn't show continuity to ground? so plugged in switch on we have continuity as explained above. unplug with switch on no continuity, plugged in switch off no continuity. So only power and switch on will it show continuity?
Had a friend check his on the phone the same way and he doesn't receive any continuity to ground like I am seeing?

3
Ham Radio Circuits and Repair / Re: RCI 2995DX NO POWER
« on: November 18, 2019, 10:27:55 PM »
OH by the way I love your videos! Helped me fix my 101E without getting any help.

Thank You for sharing your valuable knowledge we appreciate it!

4
Ham Radio Circuits and Repair / Re: RCI 2995DX NO POWER
« on: November 18, 2019, 10:23:23 PM »
NO can’t hear anything. I found Q66 only showing 13Vdc, 2.4Vdc and 13Vdc. I believe 2.4 is the collector  and should show higher voltage? I replaced it with a new Q66 (can’t recall the number) but still getting the same voltages. I tried Q66 because I found TP7 only showing 2.4V

5
Ham Radio Circuits and Repair / RCI 2995DX NO POWER
« on: September 13, 2019, 12:30:14 AM »
Ok guys I grounded test point 7 (TP7) to the RX Shielding Box, after I have no output power on any Bands, am, fm, cw....
It keys but shows NO power at all and when undereducated the needle on the RCI just bounces up and back down very quickly.

Any suggestions?

6
Amplifiers / Xforce
« on: July 30, 2019, 03:31:08 PM »
In need of a schematic for XT400

7
Test Equipment / Re: SENCORE CB42
« on: May 25, 2019, 06:53:39 PM »
Ok thank you

8
Test Equipment / SENCORE CB42
« on: May 11, 2019, 10:14:14 AM »
My CB42 frequency counter isn’t showing correct frequency, all numbers light up. I checked power to the top board and I’m seeing the 5v and 10v.
Just not sure we’re to start looking. I looked on YouTube and seen a video by The Radio Shop but it wasn’t for counter diagnosis.
Any suggestion on were to start? I did print out all the schematics he had on his site.

9
Electronic Video Blog / Re: #119 Sencore CB42 Audio Output Repair
« on: May 10, 2019, 05:15:42 PM »
Is the rest of the video posted? I have one that generates signal but counter reads wrong

Pages: [1]